SERVPRO of Lompoc

Roofers repair and install the roofs of buildings using a variety of materials, including shingles, asphalt, and metal.

Roofers typically do the following:

• Inspect problem roofs to determine the best way to repair them
• Measure roof to calculate the quantities of materials needed
• Replace damaged or rotting joists or plywood
• Install vapor barriers or layers of insulation
• Install shingles, asphalt, metal, or other materials to make the roof watertight
• Align roofing materials with edges of the roof
• Cut roofing materials to fit angles formed by walls, vents, or intersecting roof surfaces
• Cover exposed nail or screw heads with roofing cement or caulk to prevent leakage

Properly installed roofs keep water from leaking into buildings and damaging the interior, equipment, or furnishings.

There are two basic types of roofs, low-slope and steep-slope:

• Low-slope: About two-thirds of all roofs are low-slope. Most commercial, industrial, and apartment buildings have low-slope roofs. Low-slope roofs rise 4 inches or less per horizontal foot and are installed in layers.
  
  For low-slope roofs, roofers typically use several layers of roofing materials or felt membranes stuck together with hot bitumen (a tar-like substance). They glaze the top layer to make a smooth surface or embed gravel in the hot bitumen to make a rough surface.
  
  An increasing number of low-slope roofs are covered with a single-ply membrane of waterproof rubber or thermoplastic compounds.

• Steep-slope: Most of the remaining roofs are steep-slope. Most single-family houses have steep-slope roofs. Steep-slope roofs rise more than 4 inches per horizontal foot.
  
  For steep-slope roofs, roofers typically use asphalt shingles, which often cost less than other coverings. On steep-slope roofs, some roofers also install tile, solar shingles, fiberglass shingles, metal shingles, or shakes (rough wooden shingles).
  
  To apply shingles, roofers first lay, cut, and tack 3-foot strips of roofing over the entire roof. Then, starting from the bottom edge, they nail overlapping rows of shingles to the roof.

A small but increasing number of buildings now have “green” roofs that incorporate landscape roofing systems. A landscape roofing system typically begins with a single or multiple waterproof layers. After that layer is proven to be leak free, roofers put a root barrier over it, and, finally, layers of soil, in which vegetation is planted. Roofers must ensure that the roof is watertight and can endure the weight and water needs of the plants.

Janitors and building cleaners keep many types of buildings clean, orderly, and in good condition.

Janitors and building cleaners typically do the following:

• Gather and empty trash and trash bins
• Clean building floors by sweeping, mopping, or vacuuming them
• Clean bathrooms and stock them with soap, toilet paper, and other supplies
• Keep buildings secure by locking doors
• Clean spills and other hazards using sponges and squeegees
• Wash windows, walls, and glass
• Order cleaning supplies
• Make minor repairs to the building, such as changing light bulbs
• Notify managers when the building needs major repairs

Janitors and building cleaning workers keep office buildings, schools, hospitals, retail stores, hotels, and other places clean, sanitary, and in good condition. Some do only cleaning, while others have a wide range of duties.

In addition to keeping the inside of buildings clean and orderly, some janitors and building cleaners work outdoors, mowing lawns, sweeping walkways, or shoveling snow. Some janitors also monitor the heating and cooling system, ensuring that it functions properly.

Janitors and building cleaners use many tools and equipment. Simple cleaning tools may include mops, brooms, rakes, and shovels. Other tools may include snowblowers and floor buffers.

Some janitors may be responsible for repairing small problems with electricity or plumbing, such as leaky faucets.

Heating, air conditioning, and refrigeration mechanics and installers--often referred to as HVACR technicians--work on heating, ventilation, cooling, and refrigeration systems that control the air quality in many types of buildings.

Heating, air conditioning, and refrigeration mechanics and installers typically do the following:

• Travel to worksites
• Follow blueprints or other design specifications to install or repair HVACR systems
• Connect systems to fuel and water supply lines, air ducts, and other components
• Install electrical wiring and controls and test for proper operation
• Inspect and maintain customers' HVACR systems
• Test individual components to determine necessary repairs
• Repair or replace worn or defective parts

Heating and air conditioning systems control the temperature, humidity, and overall air quality in homes, businesses, and other buildings. By providing a climate controlled environment, refrigeration systems make it possible to store and transport food, medicine, and other perishable items.

Although trained to do all three, HVACR technicians sometimes work strictly with heating, air conditioning, or refrigeration systems. They also may specialize in certain types of HVACR equipment, such as water-based heating systems, solar panels, or commercial refrigeration.

Depending on the task, HVACR technicians use many different tools. For example, they often use screwdrivers, wrenches, pipe cutters and other basic handtools when installing systems. To test or install complex system components, technicians may use more sophisticated tools, such as carbon monoxide testers, voltmeters, combustion analyzers, and acetylene torches.

When working on air conditioning and refrigeration systems, technicians must follow government regulations regarding the conservation, recovery, and recycling of refrigerants. This often entails proper handling and disposal of fluids.  

Some HVACR technicians sell service contracts to their clients, providing regular maintenance of heating and cooling systems.

Other craft workers sometimes help install or repair cooling and heating systems. For example, on a large air conditioning installation job, especially one in which workers are covered by union contracts, ductwork might be done by sheet metal workers and duct installers, or electrical work by electricians. In addition, home appliance repairers usually service window air conditioners and household refrigerators. For more information on these occupations, see the profiles on sheet metal workers, electricians, or home appliance repairers.

Drywall and ceiling tile installers hang wallboards to walls and ceilings inside buildings. Tapers prepare the wallboards for painting, using tape and other materials. Many workers do both installing and taping.

Drywall installers typically do the following:

• Review design plans to minimize the number of cuts and waste of wallboard
• Measure the location of electrical outlets, plumbing, windows, and vents
• Cut drywall to the right size, using utility knives and power saws
• Fasten drywall panels to interior wall studs, using nails or screws
• Trim and smooth rough edges so boards join evenly

Ceiling tile installers typically do the following:

• Measure according to blueprints or drawings
• Nail or screw supports
• Put tiles or sheets of shock-absorbing materials on ceilings  
• Keep the tile in place with cement adhesive, nails, or screws

Tapers typically do the following:

• Prepare wall surface (wallboard) by patching nail holes
• Apply tape and use sealing compound to cover joints between wallboards
• Apply additional coats of sealing compound to create an even surface
• Sand all joints and holes to a smooth, seamless finish

Installers are also called framers or hangers. Tapers are also called finishers. Ceiling tile installers are sometimes called acoustical carpenters because they work with tiles that block sound.

Once wallboards are hung, workers use increasingly wider trowels to spread multiple coats of spackle over cracks, indentations, and any remaining imperfections. Some workers may use a mechanical applicator, a tool that spreads sealing compound on the wall joint while dispensing and setting tape at the same time.

To work on ceilings, drywall and ceiling tile installers and tapers may use mechanical lifts or stand on stilts, ladders, or scaffolds.

Construction managers plan, coordinate, budget, and supervise construction projects from early development to completion.

Construction managers typically do the following:

• Prepare and negotiate cost estimates, budgets, and work timetables
• Select appropriate construction methods and strategies
• Interpret and explain contracts and technical information to workers and other professionals
• Report on work progress and budget matters to clients
• Collaborate with architects, engineers, and other construction and building specialists
• Instruct and supervise construction personnel and activities onsite
• Respond to work delays and other problems and emergencies
• Select, hire, and instruct laborers and subcontractors  
• Comply with legal requirements, building and safety codes, and other regulations

Construction managers, often called general contractors or project managers, coordinate and supervise a wide variety of projects, including the building of all types of residential, commercial, and industrial structures, roads, bridges, powerplants, schools, and hospitals. They oversee specialized contractors and other personnel. Construction managers schedule and coordinate all design and construction processes to ensure a productive and safe work environment. They also make sure jobs are completed on time and on budget with the right amount of tools, equipment, and materials. Many managers also are responsible for obtaining necessary permits and licenses. They are often responsible for multiple projects at a time.

Construction managers work closely with other building specialists, such as architects, engineers, and a variety of trade workers, such as stonemasons, electricians, and carpenters. Projects may require specialists in everything from structural metalworking and painting, to landscaping, building roads, installing carpets, and excavating sites. Depending on the project, construction managers also may interact with lawyers and local government officials. For example, when working on city-owned property or municipal buildings, managers sometimes confer with city council members to ensure that all regulations are met.

For projects too large to be managed by one person, such as office buildings and industrial complexes, a construction manager would only be in charge of one part of the project. Each construction manager would oversee a specific construction phase and choose subcontractors to complete it. Construction managers may need to collaborate and coordinate with other construction managers who are responsible for different aspects of the project.

To maximize efficiency and productivity, construction managers often use specialized cost-estimating and planning software to effectively budget the time and money required to complete specific projects. Many managers also use software to determine the best way to get materials to the building site. For more information, see the profile on cost estimators.